White LED packaging technology continues to improve


The advent of white LEDs, the combination of phosphors and blue LEDs, can easily obtain white LEDs, which is the most mature white light package in the industry. With the advent of blue light LED, the combination of phosphor and blue LED can easily obtain white LED, which is the most mature white light packaging method in the industry. At present, white LED has become an illumination source, and general household lighting has become a reality. However, in the process of use, more white light products have a large attenuation and cannot be suitable for the lighting market. Taiwan Hongcai Optoelectronics has increased the research and development of white light for the demand of high-end lighting market, and developed low-attenuation white light products by changing the packaging process and material matching. The LED lighting industry is slightly weak.
1. Influence of wafer on white light LED light decay From the results of current experiments, the effect of wafer on light decay is divided into two categories: the first is that the material of the wafer is different, resulting in different attenuation. The commonly used blue wafer substrate material is Silicon carbide and sapphire, silicon carbide is generally designed as a single electrode, its thermal conductivity is better, sapphire is generally designed as a double electrode, heat is difficult to export, thermal conductivity is poor; second is the size of the wafer, when the wafer material is the same Different sizes vary in size.
2. Effect of solid crystal primer on white LED light decay The solid crystal glue commonly used in white LED packaging industry is epoxy resin, silicone resin and silver glue. Each of the three has its own advantages and disadvantages, and should be considered comprehensively when selecting. Epoxy resin insulation has poor thermal conductivity, but high brightness; silicone resin has better thermal conductivity than epoxy resin, and has high brightness. However, due to the proportion of silicon component, the silicone resin and the ring in the fluorescent rubber remain on the side of the solid wafer. When the oxygen resin is combined, the interlayer phenomenon will occur. After the thermal shock, the peeling will cause the dead lamp; the thermal conductivity of the silver gel is better than the former two, which can prolong the life of the LED chip, but the absorption of light by the silver paste is compared. Large, resulting in low brightness. For the two-electrode blue chip, when the crystal is fixed with silver glue, the control of the amount of glue is also very strict, otherwise it is easy to generate a short circuit, which directly affects the yield of the product.
3. Effect of Phosphor on White Light LED Light Decay There are many ways to realize white LED. The most common and most mature one is to mix blue light and yellow light into white light by applying a yellow phosphor on the blue light wafer. Therefore, the material of the phosphor has a great influence on the attenuation of the white LED. The most popular phosphors in the market are YAG yttrium aluminum garnet phosphors, silicate phosphors, and nitride phosphors. Compared with blue LED chips, phosphors have the effect of accelerating aging white LEDs, and phosphors from different manufacturers The degree of influence of fading is also different, which is closely related to the raw material composition of the phosphor. Lehman Optoelectronics uses the best material white phosphor, which makes the white LEDs have a great improvement in attenuation control compared with their peers.
4. The effect of fluorescent glue on the light decay of white LEDs Traditionally packaged white LEDs, fluorescent adhesives generally use epoxy or silica gel. After the results of light decay experiments, the life of white LEDs with silica gel is significantly better than that of epoxy resin. long. One of the reasons is that the above two methods are used to package the finished LED. The silica gel has stronger UV resistance than the epoxy resin and the heat dissipation effect of the silica gel is better than that of the epoxy resin. However, under the same conditions, the initial brightness of the silica gel is higher than that of the epoxy. The resin powder is low, the most important reason is that the refractive index of silica gel (1.3-1.4) is lower than that of epoxy resin (1.5 or more), so the initial light effect is not as high as that of epoxy resin.
5. The effect of the bracket on the light decay of white LEDs The led brackets mainly include copper brackets and iron brackets. The copper bracket has good thermal conductivity, good electrical conductivity and high price. The heat conduction and electrical conductivity of the iron bracket are relatively poor, and it is more likely to rust, but the price is cheap.
Most of the LEDs on the market use iron brackets. Brackets of different materials have different effects on the performance of LEDs, especially for light fading. This is mainly because the thermal conductivity of copper is much better than that of iron. The thermal conductivity of copper is 398W (mk), while the thermal conductivity of iron is only about 50W (mk), which is only 1/8 of the former, and the thickness of the plating layer of the stent. Also closely related. When selecting the bracket, it is also necessary to pay attention to whether the size of the cup of the bracket matches the light-emitting chip and the mold particle, and the quality of the matching quality directly affects the optical effect of the white LED, otherwise the shape of the spot is asymmetrical, and the yellow circle is easily caused. Black spots, etc., directly affect the quality of the product.
With the application of white LEDs in lighting, customer needs are constantly improving, we must constantly innovate, improve our product performance and improve our processes to meet customer needs as much as possible.

Nylon Rope

Nylon Rope,Strand Nylon Rope,3 Strand Nylon Rope,Strand Nylon Rope

Yangzhou Jieerte Steel Cable Co., Ltd , https://www.nbjieertesteelcable.com

Posted on