Pump
>> Pump Body: cast iron & support under special anti-rust treatment
>>Â Impeller: stainless steel impeller, brass impeller, ppo impeller
>>Â Mechnical Seal: carbon / ceramic / Stainless Steel
Motor
>> Bulit-in thermal protector for single phase motor
>> Motor with copper winding
>>Â Motor Housing: Steel-plate, Aluminum alloy
>> C&U bearing
>>Â AISI 304 shaft or 45#Â carbon steel
Working Range
>> Liquid: clean liquids without suspended solids, non-aggressive
>> Liquid temperature: -10ºC and +100ºC
>> Ambient temperature up to +40ºC
>> Max. working pressure 10 bar
>> Continous service S1
>> Insulation: B
>> Protection: IP44
Advantages
>> Electronic pressure switch controlled by PC clip to avoid take off pressure switch frequently.
>> Every 72h it will start for 10s in order to avoid pump locked if long time no using pump.
>> Water protection system to avoid the pump in the anhydrous state for a long time.Â
>> Delay 3s start to avoid spark-over socket, protect the personal safety.
>>Â The flow priority system, electric pump use acme, turely achieve the full pressure.Â
Application
                                                                    Â
Model | HP | W | Current (A) | Capacitor (uf) | H.Max (M) | Q.Max (L/min) | Pipe Size | Pressure Set (bar) | Tank (L) |
GDHm-125A | 0.15 | 125 | 1.5 | 8 | 30 | 32 | 1"X1" | 1.5 | 2 |
GDHm-250A | 0.35 | 250 | 3.5 | 10 | 32 | 35 | 1"X1" | 1.8 | 2 |
GDHm-370A | 0.5 | 370 | 4.5 | 10 | 36 | 36 | 1"X1" | 2.2 | 2 |
GDHm-550A | 0.75 | 550 | 2.9 | 15 | 45 | 55 | 1"X1" | 2.6 | 2 |
GDHm-750A | 1 | 750 | 3.5 | 20 | 55 | 58 | 1"X1" | 2.8 | 2 |
GDHm-1100A | 1.5 | 1100 | 4.5 | 25 | 62 | 66 | 1"X1" | 3.2 | 2 |
GDHm Automatic Self-priming Pump   Â
    Â
Item | Description | Item | Description | Item | Description | Item | Description |
11 | Press Sensor | 21 | Bearing | 31 | Screw | 41 | O-ring |
12 | Screw | 22 | Shaft Key | 32 | Cable Plug | 42 | Pressure Tank |
13 | Inlet Rubber | 23 | Rator | 33 | Cable Net | 43 | Pressure Sensor |
14 | Stainless steel Inlet | 24 | Bearing | 34 | Screw | 44 | Cover |
15 | O-ring | 25 | Stator | 35 | PC Clip | 45 | Plastic Base |
16 | Screw | 26 | Motor House | 36 | Volatede Regulator | 46 | Screw |
17 | O-ring | 27 | Terminal Box | 37 | O-ring | Â | Â |
18 | Screw | 28 | Screw | 38 | Fan | Â | Â |
19 | Front Plate | 29 | Capacitor | 39 | Screw | Â | Â |
20 | Screw | 30 | Terminal Box | 40 | Fan Cover | Â | Â |
Production Work-flow Chart of Pump
Â
                           About Us
                                 Â
FAQ
Q: Are you trading company or manufacturer ?
A: We are factory.
Q: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: What is your terms of payment ?
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment.
Pump
>> Pump Body: cast iron & support under special anti-rust treatment
>>Â Impeller: stainless steel impeller, brass impeller, ppo impeller
>>Â Mechnical Seal: carbon / ceramic / Stainless Steel
Motor
>> Bulit-in thermal protector for single phase motor
>> Motor with copper winding
>>Â Motor Housing: Steel-plate, Aluminum alloy
>> C&U bearing
>>Â AISI 304 shaft or 45#Â carbon steel
Working Range
>> Liquid: clean liquids without suspended solids, non-aggressive
>> Liquid temperature: -10ºC and +100ºC
>> Ambient temperature up to +40ºC
>> Max. working pressure 10 bar
>> Continous service S1
>> Insulation: B
>> Protection: IP44
Advantages
>> Electronic pressure switch controlled by PC clip to avoid take off pressure switch frequently.
>> Every 72h it will start for 10s in order to avoid pump locked if long time no using pump.
>> Water protection system to avoid the pump in the anhydrous state for a long time.Â
>> Delay 3s start to avoid spark-over socket, protect the personal safety.
>>Â The flow priority system, electric pump use acme, turely achieve the full pressure.Â
Application
                                                                    Â
Model | HP | W | Current (A) | Capacitor (uf) | H.Max (M) | Q.Max (L/min) | Pipe Size | Pressure Set (bar) | Tank (L) |
GDHm-125A | 0.15 | 125 | 1.5 | 8 | 30 | 32 | 1"X1" | 1.5 | 2 |
GDHm-250A | 0.35 | 250 | 3.5 | 10 | 32 | 35 | 1"X1" | 1.8 | 2 |
GDHm-370A | 0.5 | 370 | 4.5 | 10 | 36 | 36 | 1"X1" | 2.2 | 2 |
GDHm-550A | 0.75 | 550 | 2.9 | 15 | 45 | 55 | 1"X1" | 2.6 | 2 |
GDHm-750A | 1 | 750 | 3.5 | 20 | 55 | 58 | 1"X1" | 2.8 | 2 |
GDHm-1100A | 1.5 | 1100 | 4.5 | 25 | 62 | 66 | 1"X1" | 3.2 | 2 |
GDHm Automatic Self-priming Pump   Â
    Â
Item | Description | Item | Description | Item | Description | Item | Description |
11 | Press Sensor | 21 | Bearing | 31 | Screw | 41 | O-ring |
12 | Screw | 22 | Shaft Key | 32 | Cable Plug | 42 | Pressure Tank |
13 | Inlet Rubber | 23 | Rator | 33 | Cable Net | 43 | Pressure Sensor |
14 | Stainless steel Inlet | 24 | Bearing | 34 | Screw | 44 | Cover |
15 | O-ring | 25 | Stator | 35 | PC Clip | 45 | Plastic Base |
16 | Screw | 26 | Motor House | 36 | Volatede Regulator | 46 | Screw |
17 | O-ring | 27 | Terminal Box | 37 | O-ring | Â | Â |
18 | Screw | 28 | Screw | 38 | Fan | Â | Â |
19 | Front Plate | 29 | Capacitor | 39 | Screw | Â | Â |
20 | Screw | 30 | Terminal Box | 40 | Fan Cover | Â | Â |
Production Work-flow Chart of Pump
Â
                           About Us
                                 Â
FAQ
Q: Are you trading company or manufacturer ?
A: We are factory.
Q: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: What is your terms of payment ?
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment.
Aluminum alloy parts are widely used in many industries. There are many processing methods for aluminum alloy products, such as CNC machining, extrusion molding, die casting, gravity casting, forging, sand casting and so on. Each of these processing methods has its own advantages and characteristics, and some are also determined according to the structure of the product. Aluminum investment casting can reduce mold development time and cost. Precision castings with complex structures can also be easily realized with short mold development time. And it is suitable for small batch and large batch production.
SCZY is very professional in the production of metal products, especially in investment casting and precision CNC machining. We can analyze the product structure and other aspects, and can make suggestions for improvement or optimization of the unreasonable aspects of the product structure to ensure the stability of subsequent mass production. Our in-house precision CNC machining can ensure the accuracy requirements of the product, and the accuracy can reach ±0.01mm under normal conditions. We are more than happy to solve all problems.
Aluminum Casting Parts, Gravity Casting Aluminum,Aluminum Alloy Investment Castings,Aluminum Die Casting Mold,Aluminum alloy castings
Shenzhen SCZY Technology Co.,Ltd , https://www.szsczycasting.com