A dry magnetic separator for strong magnetic minerals with coarse particles, and it is also called magnetic pulley.
Magnetic Drum-Product Improvement
Cylinder could be lined with Xinhai wear- resistant rubber to prolong the service life
Â
Magnetic Drum-Advantages
Large feeding particle size(450~0mm),no classification before feeding.
High strength and high reliability of the mechanical structure guarantee the normal work of the magnetic drum in a variety of harsh environment.
Â
Magnetic Drum-Product Description
Permanent magnetic drum is also called magnetic pulley,apparatus magnetic equipment for magnetite ore, mainly used for pre concentration before fine crushing or grinding to remove the gangue, deads and tailings, and the tailings out rate is about 10%.
Magnetic Drum-Work Principle
The materials are uniformly fed to the belt. When materials go through the permanent magnetic drum, the non-magnetic and low-magnetic particles will leave the belt surface because of the centrifugal force and gravitation. Meanwhile, strong-magnetic particles are absorbed to the belt by magnetic force and then fall into the magnetic trough when the belt leaving the magnetic pulley.
Â
Magnetic Drum-Product Application
1,It is applied in lean iron roughing after the roughing crushing or middling crushingto remove deads, improve grade, and reduce the load of the next procedure.
2,For not fully reductive raw ore of hematite reduction
3,For the ceramic industry to remove iron and improve the quality of ceramic products
4,For other industries needing to remove iron, such as Burning coal, sand casting, refractory material, etc.
Technical Data:
Model | ID (mm) |
Length (mm) |
Belt width (mm) |
Average field strength of cylinder surface(mT) | Allowable torque (N.m) |
Materials Particle size (mm) |
Capacity (t/h) |
Weight (kg) |
CT-0404 | 410 | 465 | 400 | 150-160 | 1300 | 10-40 | 20-30 | 250 |
CT-0505 | 520 | 500 | 400 | 150 | 1300 | 10-40 | 20-40 | 500 |
CT-0506 | 520 | 600 | 500 | 150 | 2100 | 10-40 | 40-60 | 600 |
CT-0507 | 520 | 750 | 650 | 150 | 2120 | 10-40 | 60-80 | 700 |
CT-0707 | 750 | 750 | 650 | >160 | 2860 | 10-60 | 80-100 | 1200 |
CT-0709 | 750 | 950 | 800 | >160 | 5500 | 10-60 | 100 | 1620 |
CT-0816 | 800 | 1600 | 1400 | >160 | 9760 | 10-60 | 1OO-150 | 2850 |
CT-1010 | 1000 | 970 | 800 | 200-210 | 5590 | 10- 100 | 150-200 | 3410 |
CT-1012 | 1000 | 1170 | 1000 | >200 | 10680 | ≤100 | 200 | 4010 |
CT-1014 | 1000 | 1400 | 1200 | >200 | 12810 | ≤100 | 200 | 4600 |
CT-l0l6 | 1000 | 1600 | 1400 | 160-210 | 14920 | 10-100 | 150-200 | 5200 |
CT-12l0 | 1200 | 970 | 800 | 160-210 | 8380 | 10-100 | 150-200 | 4380 |
CT-1212 | 1200 | 1170 | 1000 | >160 | 10470 | ≤100 | 200 | 5280 |
CT-1214 | 1200 | 1400 | 1200 | >160 | 12570 | ≤100 | 200 | 6070 |
CT-1216 | 1200 | 1600 | 1400 | >160 | 14580 | ≤100 | 200 | 6670 |
A dry magnetic separator for strong magnetic minerals with coarse particles, and it is also called magnetic pulley.
Magnetic Drum-Product Improvement
Cylinder could be lined with Xinhai wear- resistant rubber to prolong the service life
Â
Magnetic Drum-Advantages
Large feeding particle size(450~0mm),no classification before feeding.
High strength and high reliability of the mechanical structure guarantee the normal work of the magnetic drum in a variety of harsh environment.
Â
Magnetic Drum-Product Description
Permanent magnetic drum is also called magnetic pulley,apparatus magnetic equipment for magnetite ore, mainly used for pre concentration before fine crushing or grinding to remove the gangue, deads and tailings, and the tailings out rate is about 10%.
Magnetic Drum-Work Principle
The materials are uniformly fed to the belt. When materials go through the permanent magnetic drum, the non-magnetic and low-magnetic particles will leave the belt surface because of the centrifugal force and gravitation. Meanwhile, strong-magnetic particles are absorbed to the belt by magnetic force and then fall into the magnetic trough when the belt leaving the magnetic pulley.
Â
Magnetic Drum-Product Application
1,It is applied in lean iron roughing after the roughing crushing or middling crushingto remove deads, improve grade, and reduce the load of the next procedure.
2,For not fully reductive raw ore of hematite reduction
3,For the ceramic industry to remove iron and improve the quality of ceramic products
4,For other industries needing to remove iron, such as Burning coal, sand casting, refractory material, etc.
Technical Data:
Model | ID (mm) |
Length (mm) |
Belt width (mm) |
Average field strength of cylinder surface(mT) | Allowable torque (N.m) |
Materials Particle size (mm) |
Capacity (t/h) |
Weight (kg) |
CT-0404 | 410 | 465 | 400 | 150-160 | 1300 | 10-40 | 20-30 | 250 |
CT-0505 | 520 | 500 | 400 | 150 | 1300 | 10-40 | 20-40 | 500 |
CT-0506 | 520 | 600 | 500 | 150 | 2100 | 10-40 | 40-60 | 600 |
CT-0507 | 520 | 750 | 650 | 150 | 2120 | 10-40 | 60-80 | 700 |
CT-0707 | 750 | 750 | 650 | >160 | 2860 | 10-60 | 80-100 | 1200 |
CT-0709 | 750 | 950 | 800 | >160 | 5500 | 10-60 | 100 | 1620 |
CT-0816 | 800 | 1600 | 1400 | >160 | 9760 | 10-60 | 1OO-150 | 2850 |
CT-1010 | 1000 | 970 | 800 | 200-210 | 5590 | 10- 100 | 150-200 | 3410 |
CT-1012 | 1000 | 1170 | 1000 | >200 | 10680 | ≤100 | 200 | 4010 |
CT-1014 | 1000 | 1400 | 1200 | >200 | 12810 | ≤100 | 200 | 4600 |
CT-l0l6 | 1000 | 1600 | 1400 | 160-210 | 14920 | 10-100 | 150-200 | 5200 |
CT-12l0 | 1200 | 970 | 800 | 160-210 | 8380 | 10-100 | 150-200 | 4380 |
CT-1212 | 1200 | 1170 | 1000 | >160 | 10470 | ≤100 | 200 | 5280 |
CT-1214 | 1200 | 1400 | 1200 | >160 | 12570 | ≤100 | 200 | 6070 |
CT-1216 | 1200 | 1600 | 1400 | >160 | 14580 | ≤100 | 200 | 6670 |
Our micromoulding manufacturing cells are the innovative answer to the growing demands from the medical, pharmaceutical, engineering and electronics industries for micro-precision components in thermoplastics. Plastic injection moulding of precision components is our core business and one at which we have excelled for over 20 years. Specialists in the development and manufacture of mould tools, plastic injection moulded components and the assembly of complex devices for the pharmaceutical, drug delivery, medical, and healthcare industries.Plastic injection moulding of precision components is our core business and one at which we have excelled for over 20 years.Precision injection moulding of all thermoplastic materials , 52 moulding machines (5T – 350T) Cleanroom moulding – Class 7 & 8 cleanrooms and White room areas , Customer specific injection moulding & assembly cells. Multi-material injection moulding,Insert & outsert moulding , Micromoulding & small component production ,Optically critical moulding, Volume production and small batch quantities Robotic handling systems and automated assembly
Precision Spare Parts Injection Mould
Precision Spare Parts Injection Mould,Various High Precision Plastic Mould,Pos Machine Injection Mold,High Precision Mold
Topwell Spring Development Ltd. , http://www.topwelldesign.com