Wire Stripping Machine/Stripping Tool/Stripping Machine

Specification
Weight: 30-31KG
Overall Dimensions: 390mm×350mm×235mm
Power: 160-300W   
Mode of Display: LCD Liquid Crystal Display Screen     
Cutting Length: 1mm - 9999mm   
Cutting Tolerance: ≤0.002×L (L = Cutting Length)      
Stripping Length: Head 0 - 35mm ,Tail 0- 15mm  
Cutting Cross-sectional Area of Wire Core:
(508C 0.2-2.5 mm^{2   Â} 508-SD 0.1- 4.5mm^2   )
(508E 0.1-8 mm^{2   Â}  508-JE 0.1- 10mm^2   )
Maximum Diameter of Conduit Pipe: ¢11
Middle-stripping: 10 places of stripping 

Material of Knife: High-quality Tungsten Steel 

1. Operating Principle

The wire is conveyed through the wire-inlet rollers and the wire-outlet rollers and the wire cutting and stripping is finished through the knife rack assembly, which are all controlled by microcomputer technology.

1. Introduction to Main Function of Every Part

1. Wire-inlet Rollers: for conveying wires and stripping wire heads.
2. Wire-outlet Rollers: for conveying wires and stripping wire tails.
3. Knife Rack Assembly: for wire cutting, head stripping and tail stripping.
4. Wire-inlet Gap Adjusting Rollers: for adjusting the wire-inlet gap, turn it down to decrease the gap and turn it up to increase the gap. 
5. Wire-outlet Gap Adjusting Rollers: for adjusting the wire-outlet gap, turn it up to increase the gap and turn it down to decrease the gap. 
6. Conduit Pipe Assembly: for ensuring the wire smooth and straight and preventing the wire from moving defectively when the wire moves from the wire-inlet rollers to the knife rack assembly. 

1. Key Points for Operation of Mechanical Parts

1. The wire is put into the wire inlet, through the wire-inlet rollers and the conduit pipe, and then onto the knife edge.   
2. Wire-inlet Gap Adjusting: adjust the gap between the two rollers through the wire-inlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped so as to ensure normal stripping of wire covering.  
3. Wire-outlet Gap Adjusting: adjust the gap between the two rollers through the wire-outlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped, and adjust the indicator light of wire breakage at the critical state between on and out, then turn up for half circle. If the machine still stops because the wire knobs, adjust the gap a little smaller. 







 






Specification
Weight: 30-31KG
Overall Dimensions: 390mm×350mm×235mm
Power: 160-300W   
Mode of Display: LCD Liquid Crystal Display Screen     
Cutting Length: 1mm - 9999mm   
Cutting Tolerance: ≤0.002×L (L = Cutting Length)      
Stripping Length: Head 0 - 35mm ,Tail 0- 15mm  
Cutting Cross-sectional Area of Wire Core:
(508C 0.2-2.5 mm^{2   Â} 508-SD 0.1- 4.5mm^2   )
(508E 0.1-8 mm^{2   Â}  508-JE 0.1- 10mm^2   )
Maximum Diameter of Conduit Pipe: ¢11
Middle-stripping: 10 places of stripping 

Material of Knife: High-quality Tungsten Steel 

1. Operating Principle

The wire is conveyed through the wire-inlet rollers and the wire-outlet rollers and the wire cutting and stripping is finished through the knife rack assembly, which are all controlled by microcomputer technology.

1. Introduction to Main Function of Every Part

1. Wire-inlet Rollers: for conveying wires and stripping wire heads.
2. Wire-outlet Rollers: for conveying wires and stripping wire tails.
3. Knife Rack Assembly: for wire cutting, head stripping and tail stripping.
4. Wire-inlet Gap Adjusting Rollers: for adjusting the wire-inlet gap, turn it down to decrease the gap and turn it up to increase the gap. 
5. Wire-outlet Gap Adjusting Rollers: for adjusting the wire-outlet gap, turn it up to increase the gap and turn it down to decrease the gap. 
6. Conduit Pipe Assembly: for ensuring the wire smooth and straight and preventing the wire from moving defectively when the wire moves from the wire-inlet rollers to the knife rack assembly. 

1. Key Points for Operation of Mechanical Parts

1. The wire is put into the wire inlet, through the wire-inlet rollers and the conduit pipe, and then onto the knife edge.   
2. Wire-inlet Gap Adjusting: adjust the gap between the two rollers through the wire-inlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped so as to ensure normal stripping of wire covering.  
3. Wire-outlet Gap Adjusting: adjust the gap between the two rollers through the wire-outlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped, and adjust the indicator light of wire breakage at the critical state between on and out, then turn up for half circle. If the machine still stops because the wire knobs, adjust the gap a little smaller. 







 

HVAC Actuator

Automotive air conditioning (HVAC) actuators are used for damper control to create a comfortable interior environment by changing damper Angle, adjusting supply air temperature, blowing mode, internal circulation, etc. Automatic air conditioning Temperature Control system working principle: automotive Automatic Temperature Control (ATC), commonly known as constant temperature air conditioning system; Once the target temperature is set, the ATC system automatically controls and adjusts the temperature in the car to maintain the set value.

Hvac Actuator,Automotive Hvac Actuators Kit,Automotive Hvac Actuator Adapter,Automotive Hvac Actuator

Haoyong Automotive Controls , https://www.haoyongauto.com