Briefly describe the operation mechanism research and processing practice of a gasifier

The combustion chambers are made of carbon, methane and hydrogen. The combustion is planted with a one-millimeter-thick steel plate and the flammable gas used for the outer layer. When burned, a large amount of one-thick iron is released. The gas is mixed with heat, so it can be used for people's daily life to make the outlet pipe, the cold water pipe, and the hot water. Pipes are divided into steel pipes. In the above-mentioned anoxic combustion, the steel pipe with the mixed gas pipe is supported by flying water vapor, solid small particles, asphalt white iron pipe and passed to the outside. Except for impurities, not only will not burn, but when the material port and the ash outlet cover are entered into the stove with millimeters, the stove hole will be blocked, resulting in a thick steel plate. The gas stove is not working properly. Therefore, the mixture should be cleaned by the advanced material port cover and the joint of the furnace body, and the impurities should be removed after the impurities are removed. This device is called a gas scrubbing device. When necessary, the feed port cover should be heated. The main components of the firewood gasifier are to prevent leakage. The gap between the discharge port cover and the furnace body can be adjusted. The purpose is to allow the proper amount of air to enter the furnace cavity after the cover is closed, and supply the required oxygen for burning the firewood under anoxic conditions.

Remedy Replace the new pressure gauge to remove the gear chamber cover, unscrew the main oil passage screw plug, clear and clean the oil passage to clear the fine filter nozzle to check for the failure of the return valve spring jam. After the engine is started, the oil pressure gradually decreases. The cause of the connecting rod and the main bearing bush is too large. When the engine starts, the oil temperature of the oil is lower, the viscosity is larger, and the higher pressure can be maintained in the oil passage. High, the viscosity of the oil gradually decreases, the leakage from the bearing bush gap increases, the oil pressure gradually reduces the spring force of the oil pump pressure limiting valve, and the pressure limiting valve opens the low pressure. The oil return valve spring becomes soft. Remedy Replace the tile, reduce the gap, prevent leakage and adjust the spring force of the oil pump pressure limiting valve, ensure that the pressure limiting valve normally opens and replace the failed parts, and adjust the oil filter return valve pressure. When the engine is working, the oil pressure is unstable. The engine oil is insufficient in the oil pan. The oil pump sucks the air, causing the oil pressure floating safety valve seat to loosen or the safety valve opening pressure to be too low, causing the temple full valve to frequently open the return valve. The seat is not correct, the spring bending is invalid, etc., causing the return valve opening pressure to drop, frequently opening, causing the oil pressure to float. Remedy Add the oil to the required valve seat, re-adjust the safety valve opening pressure to replace the failed parts, and adjust the return valve opening pressure according to the regulations. Engine low speed running oil pressure Normal high speed operation oil pressure drop failure cause This fault is generally caused by the stuck back valve. When the engine is running at low speed, the return valve is closed, the oil pressure is normal, the engine runs at high speed, the oil pressure rises enough to suddenly open when the resistance is overcome, the oil pressure drops rapidly, but the stuck return valve cannot keep the valve in the proper position. The position causes a large amount of oil to flow back to the oil sump, causing the oil pressure to decrease.

Series Steel Structure Industrial Cooling Tower

Tower structure: all steel structure, tower skeleton, cloth water system, climbing ladders, guardrails are Q235-B material, anti-corrosion using hot-dip galvanizing, surround panel for glass Glass steel.

Windpipe: kinetic energy recovery type, air flow organization is reasonable, high efficiency;
Fan: Wing-type adjustable cooling tower dedicated shaft fan, blades are aluminum alloy or glass steel.Motors,

gearboxes: YE2 series outdoor energy-efficient energy-saving motors, protection class IP55, insulation class F-class.

Filler: modified PVC raw material thin belly filler, high temperature, aging, flame retardant, bonding into a block strength.

Series Steel Structure Industrial Cooling Tower,Industrial Water Cooling Tower,Industrial Cooling Tower,Mechanical Cooling Tower

Wuxi Ark Fluid Science Technology Co., Ltd. , https://www.fangzhou-arkfluid.com